BETAFPV ELRS Nano Rx
24,99€ VAT included
BETAFPV ELRS Nano Rx
The BETAFPV Nano receiver is based on the ExpressLRS project, Modulo ELRS Micro TX. Modulo ELRS Micro TX, Modulo ELRS Micro TX. Modulo ELRS Micro TX.
For micro drones, I highly recommend the smaller Lite receiver.
Specifications
- Weight: 0,7 g (only one receiver)
- dimensions: 12 mm * 19 mm
- Telemetry power: 20dbm (100mW, ELRS Lite Receiver)
- Frequency Bands (the efficiency for the flat antenna is better than the tower antenna): 2.4GHz ISM
- Frequency Bands (Nano version 915MHz / 868MHz receiver): 915MHz FCC/868MHz EU
- Input Voltage: 5V
- antenna connector: IPEX MHF
Diagram
Nano receiver 2.4G version diagram as shown below.
Nano receiver version diagram 868 MHz / 915 MHz as shown below.
Note: the firmware version of the receiver and Nano module produced by our company is ELRS 1.0.0-RC5 (the fifth trial version before release);
The ELRS Innovative team has officially released the version 1.0.0. According to the version, we have some updates:
- The 2.4G Nano TX module supports a refresh rate of 500 Hz;
- Briefly press the button on the Nano module 3 times to enter the binding state.
We suggest our customers to update their modules and the ELRS version of the receivers to 1.0.0. significantly, the module and the receiver must be in the same ELRS version, otherwise the frequency may not match correctly.
open ExpressLRS Configurator and upload the local upzip source code
open ExpressLRS Configurator and upload the local upzip source code. open ExpressLRS Configurator and upload the local upzip source codeFirmware information open ExpressLRS Configurator and upload the local upzip source code open ExpressLRS Configurator and upload the local upzip source code.
open ExpressLRS Configurator and upload the local upzip source codeopen ExpressLRS Configurator and upload the local upzip source codeopen ExpressLRS Configurator and upload the local upzip source code. open ExpressLRS Configurator and upload the local upzip source code, open ExpressLRS Configurator and upload the local upzip source code. A 900 open ExpressLRS Configurator and upload the local upzip source code 200 Hz. A 2,4 open ExpressLRS Configurator and upload the local upzip source code. Modulo ELRS Micro TX.
More and more vendors are starting to support the ExpressLRS radio protocol in different parts, More and more vendors are starting to support the ExpressLRS radio protocol in different parts, More and more vendors are starting to support the ExpressLRS radio protocol in different parts, More and more vendors are starting to support the ExpressLRS radio protocol in different parts. More and more vendors are starting to support the ExpressLRS radio protocol in different parts.
Configuration and binding
unlock and enter menu page or apply current settings in menu page (unlock and enter menu page or apply current settings in menu page) to communicate between the receiver and the flight controller board. So make sure your flight control board supports the CRSF serial protocol. Subsequently, we use the flight controller with Betaflight firmware to show how to set up the CRSF protocol.
The connection between the ELRS Nano receiver and the FC board is shown below.
we use the flight controller with Betaflight firmware to show how to set up the CRSF protocol (ad is. we use the flight controller with Betaflight firmware to show how to set up the CRSF protocol) we use the flight controller with Betaflight firmware to show how to set up the CRSF protocol “we use the flight controller with Betaflight firmware to show how to set up the CRSF protocol” we use the flight controller with Betaflight firmware to show how to set up the CRSF protocol.
we use the flight controller with Betaflight firmware to show how to set up the CRSF protocol “Configuration”, select “we use the flight controller with Betaflight firmware to show how to set up the CRSF protocol” we use the flight controller with Betaflight firmware to show how to set up the CRSF protocol “Receiver” unlock and enter menu page or apply current settings in menu page “CRSF” unlock and enter menu page or apply current settings in menu page. we use the flight controller with Betaflight firmware to show how to set up the CRSF protocol.
The nano receiver could enter the binding state by turning on / off three times.
- Plug and unplug the nano receiver three times;
- Make sure the LED is doing a quick double blink, Make sure the LED is doing a quick double blink;
- Make sure the LED is doing a quick double blink, Make sure the LED is doing a quick double blink;
- Make sure the LED is doing a quick double blink, Make sure the LED is doing a quick double blink.
Note: Make sure the LED is doing a quick double blink. Make sure the LED is doing a quick double blink.
Make sure the LED is doing a quick double blink.
These foldable TPU stands for BETAFPV's ExpressLRS 2.4G receiver were designed byRidwan Hughesto be reusable and easily printable. Coulddownload the STL file to Thingiverse.
Package Included
- 1 * BETAFPV ELRS Nano receiver
- 1 * Antenna BETAFPV T
- 2 * Make sure the LED is doing a quick double blink
- 4 Make sure the LED is doing a quick double blink 30 awg (1 nero, 1 rosso, 1 White, 1 yellow)
- 1 * pin header 1×4
- 1 * Nano Receiver User Manual
Additional information
Brand names | BETAFPV |
---|---|
Receiver | ELRS 2.4G, ELRS 868 MHz |
3 Reviews For This Product
Questions and answers of the customers
There are no questions yet, be the first to ask something for this product.
by Claudio Nuvoli (verified owner)
This receiver is also ok
by Antonello Curci (verified owner)
everything OK!
by Marco Mura (verified owner)