Iflight Chimera7 Pro 6S analogico

529,98569,97 VAT included

  • TBS Crossfire Nano RX
  • ELRS 915MHz
  • ELRS 2.4GHz
  • Without Receiver
Clear

PRODUCT DESCRIPTION

We present what has been requested for too long already! An iFlight bird from 7 super efficient long range inch that can go where you couldn't go before and can carry bigger batteries to get the flight time to navigate the swiss alps, if you want! A super stiff chassis for minimal resonance and XING2 motors 2809 for maximum propeller control from 7 inch. Fly with large high-mounted batteries, or even larger low-mounted batteries, 6 recommended cells or 5 cells for a slow cruise. But whatever style you fly, a Lipo or Lion pack will simply do the job. 5S recommended 3.000 mAh above (slow cruise) o 6S 2.500 mAh above.

GPS functionality to find your way back and Betaflight GPS Rescue mode ready for installation (default OFF to prevent unexpected behavior; installation instructions included). Vertical and horizontal TBS Crossfire antenna mounts are included to cover you and the dead ends of the antenna just in case. Universal GoPro TPU bottom support included; fits your original GoPro bracket and our TPU GoPro protectors (additional).

Principale Changelog da Chimera7 a Chimera7 Pro:

Stack SucceX-D F7 V2.2 (F7+50A ESC) updated to BLITZ F722 Stack (F7 V1.1 + 55A 4in1 ESC)

– New lightweight design of the side panels – Keep your rig clean

– XING 2806.5 updated to XING2 2809 1250KV

– Frame from 7 thumbs updated to 7,5 inch

EMPHASIZES:

– Battery voltage LED status indicator (IF logo illuminated on the bottom)

– GoPro TPU bottom support (GoPro protection not included)
– Lightweight side panel design – Keep your rig clean

– Efficient wide stator motors XING2 2809 1250KV

– Pre-installed GPS for greater remote safety

– 360 ° TPU protection , FPV cam protection

– Rigid arm design from 6 mm for greater rigidity

– Top and bottom battery mounting option

you will be able to bring your expensive equipment back to you. In case of problems with signal interference:

– This is your first BNF or are you just getting started with FPV? This article could probably help: General guide // iFlight BNF

– Don't worry about tuning, we have already done it for you! you will be able to bring your expensive equipment back to you. In case of problems with signal interference!

To restore lost songs or updates, check out our linked article on “Firmware/Factory Dumps”

– The corner mode (self-balancing level mode) is enabled by default to make sure your first flight doesn't end up in a mess!

Please check out our linked article on “The corner mode, The corner mode”

– GPS Rescue is OFF by default to prevent unwanted or unexpected drone behavior.

Please check out our linked article on “GPS rescue mode // Configuration”

Specifications:

– Weight: 695 g (without battery and GoPro support)

– Total size: 258 * 200 mm (body size)

– upper plate Thickness (medium): 3 mm

– Distance from bottom to top: 20-29 mm

– ESC: BLITZ E55 4-IN-1 2-6S ESC

– bottom plate Thickness: 3 mm

– Camera plate thickness: 3 mm

– upper plate Thickness: 3 mm

– Geometry: DC (DeadCat)

– Eliche HQ 7.5X3.7X3

– arm Thickness: 6 mm

-XING2 2809 1250KV

– FC: BLITZ F722

ELECTRONICS // BLITZ F7 Stack (F7 V1.1 + 55A 4in1 ESC) :

FC // BLITZ F722 flight controller

  • Assembly diagram: PCB hole diameter 30,5 * 30,5 mm / 4 mm
  • Smartaudio protocol / IRC Tramp VTX supported
  • The corner mode: IFLIGHT_BLITZ_F722
  • Motor outputs: 4x (SH1.0 connector)
  • Flash: 32 MB (flash Blackbox)
  • I2C series: SDA pads / SLA
  • dimensions: 36,5*35 mm
  • Barometer: DPS310
  • Chip OSD: AT7456E
  • Controller LED: Yup
  • MCU: STM32 F722
  • Acoustic signal: Yup
  • Gyroscope: BMI270
  • Weight: 7,8 g
  • UART: 6

 

ESC // BLITZ E55 4-IN-1 2-6S 55A ESC

  • Supports: DShot DShot150/300/600/MultiShot/OneShot ecc.
  • Mounting Holes: 30,5 * 30,5 mm/Φ4 mm
  • Target: IFLIGHT_BLITZ_G2
  • Supports the’ input Lipo 2-6S
  • Current sensor: Yup
  • Constant: 55 ampere
  • Current rate: 200
  • Bursting: 65 A
  • Weight: 15,3 g
  • MCU: G071
  • BEC: no

 

VT X// BLITZ 1.6W VTX regolable

  • Betaflight IRC Tramp Configuration: Download the attached VTX table for Betaflight!
  • Values ​​from the IRC Tramp VTX table: 25 mW/400 mW/800 mW/1600 mW
  • Power Levels: PIT/ 25mW/400mW/800mW/1600mW
  • All of our VTX tables can also be found here: LINK
  • Light: 18,9 g (antenna excluded)
  • Assembly diagram: 30,5×30,5 mm/Φ3
  • Channels: 40 (including Race tire)
  • Telemetry VTX: IRC Tramp
  • Input Voltage: 7V ~ 36V
  • Interface: MMCX

Link to the product

Chimera7 Pro Analog BNF Components and parts included

  • 4 x eliche HQ 7.5X3.7X3 CW + 4 x HQ 7.5X3.7X3 CCW (the color may vary)
  • 1 fotocamera RaceCam R1 Mini 1200TVL 2.1mm 19*19
  • 1 x antenna Albatross RHCP 5.8GHz SMA FPV
  • 2 x iFlight Lipo Strap 20*250mm (Nero)
  • 1 x Chimera7 Pro pre-built and tested

Advice:

VTX is set to 25 mW by default! Power levels higher than 25 mW require a HAM license or must be approved by local authorities! Make sure you fly on legal frequencies and use our Betaflight VTX charts prepared for your region.

PLEASE NOTE: TO ENSURE MAXIMUM QUALITY, EACH MODEL WILL BE INSPECTED BY OUR STAFF BEFORE IT IS SHIPPED.

Additional information

Receivers

TBS Crossfire Nano RX, ELRS 915MHz, ELRS 2.4GHz, Without Receiver

Brand names

IFLIGHT

Be the first to review “Iflight Chimera7 Pro 6S analogico”

Your email address will not be published. Required fields are marked *

Reviews

There are no reviews yet.

Questions and answers of the customers

There are no questions yet, be the first to ask something for this product.

Main Menu

Iflight Chimera7 Pro 6S analogico

529,98569,97 VAT included

Add to Cart
×

How can we help you?

If you want more shipping information, payments, returns and sizes can read here. If you want assistance you can write us an email on info@drone24hours.com O Whatsapp by clicking below.

×