Stacks Holybro Kakute H7 e Tekko32 4in1 65A

224,98 VAT included

Out of stock

Receive Email when available!

The Holybro Kakute H7 v2 flight controller is packed with features including built-in Bluetooth, HD camcorder socket, doppie porte ESC plug-and-play 4in1, pit switch ON/OFF VTX from 9 V, barometer, OSD, 6 UART, 128 MB of flash for recording, 5 V e 9V BEC, larger solder pad with simple layout and more.

The Kakute H7 v2 builds on the best features of its F7 predecessor and further improves the hardware components and layout. With the integrated additional integrated Bluetooth chip, you can wirelessly configure and tune your phone with the SpeedyBee app for Android and IOS. The Kakute H7 is DJI HD ready. It has a simple plug-and-play port with a built-in 9V regulator designed to power your HD video transmitter such as DJI / Caddx FPV Air Unit and Caddx Vista while supporting analog system.

It features a “VTX ON/OFF Pit Switch” built-in that allows you to turn off the video transmitter completely using a switch on the RC transmitter. Great if you are working on your drone, waiting for the GPS to get a fix, preparing you for a race while avoiding overheating or interfering with others in flight. It has 6 dedicated UART ports with built-in reverse for peripherals (UART2 is used for Bluetooth telemetry), a flash yes 128 MB for registration, dual plug-and-play 4in1 ESC connectors, which allow easy plug-and-play support for x8 and Octocopter configuration and keeping it simple and clean. The integrated BetaFlight OSD makes it easy to view important information on the FPV display such as battery voltage, flight time, notices, RSSI, smart audio functions and more. It is also ready for autonomous flight with the onboard barometer.

For wiring guide, view Wiring diagram at Holybro Doc.

Specifications

  • MCU – Processor a 32 STM32H743 bit working a 480 MHz
  • IMU – BMI270
  • Barometer – BMP280
  • OSD-AT7456E
  • Integrated Bluetooth chip – ESP32-C3
    • Compatible with SpeedyBee IOS and Android
    • Note: Built-in Bluetooth is set to turn off automatically when the flight controller is unlocked (armed) and automatically turn on when the flight controller is locked (unarmed).
  • VTX ON/OFF Pit Switch ā€“ The switch can be enabled using USER1 in the Betaflight Mode tab.
    • Warning: do not enable this pit switch if you are using the DJI FPV remote control
  • 6x UART (1,2,3,4,6,7; UART2 is used for Bluetooth telemetry)
  • 9 uscite PWM (8 motor outputs, 1 LED)
  • 2x porta JST-SH1.0_8pin (ESC 4in1, compatible x8 / Octocopter)
  • 1x porta JST-GH1.25_6pin (for HD systems such as Caddx Vista and Air Unit)
  • Battery input voltage: gives 7 In a 42 V
  • BEC 5V 2A cont.
  • BEC 9V 1.5A cont.
  • mounting: hole from 30,5 x 30,5 mm / Ī¦4 mm with Ī¦3 mm eyelets
  • Dimension – 35x35mm
  • Weight: 8 g

Tekko32 F4 Metal 4in1 65A ESC (65A)

MCU F4 @150Mhz / Dshot150/300/600/1200/2400 / Uscita PWM: 16k ~96k PWM / 4~6S / BLHELI32
Dshot150/300/600/1200/2400. Powerful and reliable metal case MOSFET 4in1 ESC with smooth control and fast response.
Rev v1.7 Updated: ammeter scale ratio: 180

Features:

  • New and faster MCU F4 a 150 Mhz (compared to F3 a 108 Mhz e F0 a 48 Mhz)
  • Frequenza PWM: at 16k to 96k
  • Metal-cased MOSFET for excellent heat dissipation
  • Huge built-in noise filtering capacity to 2068uf
  • Design PCB in rame da 3 Design PCB in rame da
  • Separate drive and control circuit, this broadens the current capability of the drive circuit while reducing electrical noise to the control circuit.

Specifications

  • Direct current: 65A x4
  • Burst Current: 75A x4
  • Support 4-6S battery
  • Support DShot 150/300/600/1200 e MultiShot/OneShot/Proshot/PWM ecc.
  • Design PCB in rame da
  • Integrated analog current sensor
  • No BEC output
  • Firmware BLHeli_32
  • Design PCB in rame da (highly recommended for 6s setup)
  • Design PCB in rame da: 180
  • dimensions: 43 x 44 mm / Weight: 15,8 g
  • Mounting Holes: M4 30.5×30,5 mm (M3 gaskets included)
Note:
The airflow for the ESC is very important if you want to run this high current 4in1.
The battery cable (Design PCB in rame da) must be at least 12 AWG and well soldered.

Package Included

SKU20196 Kakute H7 V2&Tekko32 F4 Metallo 4in1 65A ESC STACK

  • 1 Pila Kakute H7 V2
  • 1x electrolytic capacitor: 1000uF 35v
  • 1 cable 8 pin a 8 pin with step from 1 mm e 65 mm
  • 1 cable 8 pin a 8 pin with step from 1 mm e 25 mm
  • 1x JST GHR cable from 8 pin a JST GHR 6 pin yes 80 mm (for DJI / Caddx HD system)
  • 1 cavo JST GHR a 6 pin yes 100 mm (per sistemi Caddx HD)

SKU20197 Kakute H7 V2&Tekko32 F4 Metal 4in1 65A ESC&Atlatl HV V2 STACK

  • 1x STACK Kakute H7 BT
  • 1x electrolytic capacitor: 1000uF 35v
  • 1 cable 8 pin a 8 pin with step from 1 mm e 65 mm
  • 1 cable 8 pin a 8 pin with step from 1 mm e 25 mm
  • 1x JST GHR cable from 8 pin a JST GHR 6 pin yes 80 mm (for DJI / Caddx HD system)
  • 1 cavo JST GHR a 6 pin yes 100 mm (per sistemi Caddx HD)
  • 1 SMA-MMCX cable from 80 mm
  • 1 cavo JST GHR a 4 pin yes 150 mm

Additional information

Brand names

HOLYBRO

PROCESSOR

H7

AMPERAGE

65A

FIRMWARE ESC

BLHeli_32

CONNECTOR

USB-C

GYRO

BMI270

UART

6

VOLTAGE (V)

LiPo 4S/14.8V, LiPo 6S/22.2V

VERSION

DIGITAL

Be the first to review ā€œStacks Holybro Kakute H7 e Tekko32 4in1 65A”

Your email address will not be published. Required fields are marked *

Reviews

There are no reviews yet.

Questions and answers of the customers

There are no questions yet, be the first to ask something for this product.

Main Menu

Stacks Holybro Kakute H7 e Tekko32 4in1 65A

224,98 VAT included

×

How can we help you?

If you want more shipping information, payments, returns and sizes can read here. If you want assistance you can write us an email on info@drone24hours.com O Whatsapp by clicking below.

×